document number: 31006 for technical questions, contact: thinfilmchip@vishay.com www.vishay.com revision: 31-jan-12 345 tnpw vishay high stability thin film chip resistors this document is subject to change without notice. the products described herein and this document ar e subject to specific disclaimers, set forth at www.vishay.com/doc?91000 tnpw precision thin film flat chip resistors are the perfect choice for most fields of modern electronics where reliability and stability is of major concern. typical applications include industrial, medical equipment, and those, which are not necessarily subject to the rohs directive like military and avionics. features ? excellent overall stability at different environmental conditions ? 0.05 % (1000 h rated power at 70 c) ? low temperature coefficient and tight tolerances ( 0.1 %; 10 ppm/k) ? metal film layer on high quality ceramic ? snpb termination plating, minimum 6 % pb applications ? avionics ? military ? medical equipment ? industrial equipment notes ? tnpw 0402 without marking. (1) size not specified in en 140401-801. (2) rated voltage . the power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). the rated dissipati on applies only if the permitted film temper ature is not exceeded. (3) measuring conditions in a ccordance with en 140401-801. standard electrical specifications tnpw0402 tnpw0603 tnpw0805 tnpw1206 tnpw1210 (1) tnpw2010 tnpw2512 (1) metric size rr 1005m rr 1608m rr 2012m rr 3216m rr 3225m rr 5025m rr 6332m resistance range 10 ? to 100 k ? 10 ? to 332 k ? 10 ? to 1 m ? 10 ? to 2 m ? 10 ? to 3.01 m ? 10 ? to 4.99 m ? 10 ? to 8.87 m ? resistance tolerance 1 %; 0.5 %; 0.1 % temperature coefficient 50 ppm/k; 25 ppm/k; 15 ppm/k; 10 ppm/k 50 ppm/k; 25 ppm/k rated dissipation, p 70 (2) 0.063 w 0.1 w 0.125 w 0.25 w 0.33 w 0.4 w 0.5 w operating voltage, u max. ac/dc 50 v 75 v 150 v 200 v 200 v 300 v 300 v permissible film temperature, ? f max. 125 c (155 c) operating temperature range - 55 c to 125 c (155 c) thermal resistance (3) 870 k/w 550 k/w 440 k/w 220 k/w 170 k/w 140 k/w 110 k/w insulation voltage: u ins 1 min 75 v 100 v 200 v 300 v 300 v 300 v 300 v continuous 75 v 75 v 75 v 75 v 75 v 75 v 75 v failure rate: fit observed ?? 0.3 x 10 -9 /h ?? 0.3 x 10 -9 /h ?? 0.3 x 10 -9 /h ?? 0.3 x 10 -9 /h ?? 0.3 x 10 -9 /h ?? 0.3 x 10 -9 /h ?? 0.3 x 10 -9 /h p x r
www.vishay.com for technical questions, contact: thinfilmchip@vishay.com document number: 31006 346 revision: 31-jan-12 tnpw vishay high stability thin fi lm chip resistors this document is subject to change without notice. the products described herein and this document ar e subject to specific disclaimers, set forth at www.vishay.com/doc?91000 dimensions dimensions and mass type l (mm) w (mm) h (mm) t1/t2 (mm) mass (mg) tnpw0402 1.0 0.05 0.5 0.05 0.35 0.05 0.2 0.10 0.65 tnpw0603 1.6 0.10 0.85 0.10 0.45 0.10 0.3 0.20 2 tnpw0805 2.0 0.15 1.25 0.15 0.45 0.10 0.4 0.20 5.5 tnpw1206 3.2 0.15 1.6 0.15 0.55 0.10 0.5 0.25 10 tnpw1210 3.2 0.15 2.45 0.15 0.60 0.15 0.5 0.25 16 tnpw2010 5.0 0.15 2.5 0.15 0.60 0.15 0.6 0.25 28 tnpw2512 6.3 0.20 3.1 0.15 0.60 0.15 0.6 0.25 39 solder pad dimensions type reflow soldering wave soldering a (mm) b (mm) l (mm) a (mm) b (mm) l (mm) tnpw0402 0.4 0.6 0.5 - - - tnpw0603 0.5 0.9 1.0 0.9 0.9 1.0 tnpw0805 0.7 1.3 1.2 0.9 1.3 1.3 tnpw1206 0.9 1.7 2.0 1.1 1.7 2.3 tnpw1210 0.9 2.5 2.0 1.1 2.5 2.3 tnpw2010 1.0 2.5 3.9 1.2 2.5 3.9 tnpw2512 1.0 3.2 5.2 1.2 3.2 5.2 temperature coefficient and resistance range type tcr tolerance resistance e-series tnpw0402 50 ppm/k 1 % 10r to 100k 24; 96 0.5 % 10r to 100k 24; 192 0.1 % 47r to 100k 25 ppm/k 1 % 10r to 100k 24; 96 0.5 % 10r to 100k 24; 192 0.1 % 47r to 100k 15 ppm/k 0.1 % 10 ppm/k 0.1 % tnpw0603 50 ppm/k 1 % 10r to 332k 24; 96 0.5 % 10r to 332k 24; 192 0.1 % 25 ppm/k 1 % 10r to 332k 24; 96 0.5 % 10r to 332k 24; 192 0.1 % 15 ppm/k 0.1 % 47r to 332k 10 ppm/k 0.1 % tnpw0805 50 ppm/k 1 % 10r to 1m0 24; 96 0.5 % 10r to 1m0 24; 192 0.1 % 25 ppm/k 1 % 10r to 1m0 24; 96 0.5 % 10r to 1m0 24; 192 0.1 % 15 ppm/k 0.1 % 47r to 1m0 10 ppm/k 0.1 %
document number: 31006 for technical questions, contact: thinfilmchip@vishay.com www.vishay.com revision: 31-jan-12 347 this document is subject to change without notice. the products described herein and this document ar e subject to specific disclaimers, set forth at www.vishay.com/doc?91000 tnpw high stability thin fi lm chip resistors vishay note ? the product can be ordered using either the part number or the product description. ? for ordering tnpw e3 with lead free termi nations please refer to latest edition of datasheet tnpw e3, document number 28758. tnpw1206 50 ppm/k 1 % 10r to 2m0 24; 96 0.5 % 10r to 2m0 24; 192 0.1 % 25 ppm/k 1 % 10r to 2m0 24; 96 0.5 % 10r to 2m0 24; 192 0.1 % 15 ppm/k 0.1 % 47r to 2m0 10 ppm/k 0.1 % tnpw1210 50 ppm/k 1 % 10r to 3m01 24; 96 0.5 % 10r to 3m01 24; 192 0.1 % 47r to 2m13 25 ppm/k 1 % 10r to 3m01 24; 96 0.5 % 10r to 3m01 24; 192 0.1 % 47r to 2m13 15 ppm/k 0.1 % 10 ppm/k 0.1 % tnpw2010 50 ppm/k 1 % 10r to 4m99 24; 96 0.5 % 10r to 4m99 24; 192 0.1 % 47r to 1m0 25 ppm/k 1 % 10r to 4m99 24; 96 0.5 % 10r to 4m99 24; 192 0.1 % 47r to 1m0 tnpw2512 50 ppm/k 1 % 10r to 8m87 24; 96 0.5 % 10r to 8m87 24; 192 0.1 % 47r to 1m0 25 ppm/k 1 % 10r to 8m87 24; 96 0.5 % 10r to 8m87 24; 192 0.1 % 47r to 1m0 temperature coefficient and resistance range type tcr tolerance resistance e-series part number and product description part number: tnpw12061k32deta type/size resistance tolerance tcr packaging special tnpw0402 tnpw0603 tnpw0805 tnpw1206 tnpw1210 tnpw2010 tnpw2512 r = decimal k = thousand m = million (4 digits) b = 0.1 % d = 0.5 % f = 1.0 % h = 50 ppm/k e = 25 ppm/k x = 15 ppm/k y = 10 ppm/k ta td cn ty tc up to 2 digits blank = standard product description: tnpw-1206 1.32k 0.5 % t-9 rt1 tnpw-1206 1.32k 0.5 % t-9 rt1 type resistance tolerance tcr packaging tnpw-0402 tnpw-0603 tnpw-0805 tnpw-1206 tnpw-1210 tnpw-2010 tnpw-2512 examples: 1k32 = 1320 ? 99.68k = 99 680 ? 360 = 360 ? 0.1 % 0.5 % 1.0 % t- 2 = 50 ppm/k t- 9 = 25 ppm/k t- 1 0 = 15 ppm/k t- 1 3 = 10 ppm/k rt1 rt7 r52 r75 rt6 npw12061k t 32deta
www.vishay.com for technical questions, contact: thinfilmchip@vishay.com document number: 31006 348 revision: 31-jan-12 tnpw vishay high stability thin fi lm chip resistors this document is subject to change without notice. the products described herein and this document ar e subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) 1000 pieces packaging is avail able only for precision resistors with to lerance 0.1 % and temperature coefficient ? 25 ppm/k. description production is strictly controlle d and follows an extensive set of instructions established for reproducibility. a homogeneous film of metal alloy is deposited on a high grade ceramic substrate and conditioned to achieve the desired temperature coefficient. a special laser is used to achieve the target value by smoothly cutting a meander groove in the resistive layer without damaging the ceramics. a further conditioning is applied in order to stabilize the trimming result. the resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. the result of the determined production is verified by an extensive testing procedu re on 100 % of the individual chip resistors. this includes pulse load screening for the elimination of products with a potential risk of early life failures according to en 140401- 801, 2.1.2.2. only accepted products are laid directly into the tape in accordance with en 60286-3. assembly the resistors are suitable for processing on automatic smd assembly systems. they are suit able for automatic soldering using wave, reflow or vapour phase as shown in iec 61760-1. the encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. the suitability of conformal coatings, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. solderability is specified for 2 years after production or re-qualification. the permitted storage time is 20 years. related products the lead free version tnpw e3 can be used as drop in replacement for the tnpw whenever lead bearing terminations are not mandatory. for ordering tnpw e3 please refer to latest edition of datasheet tnpw e3, document number 28758. tnps .... escc high-reliability thin film chip resistors are the premium choice for design and manufacture of equipment, where matured technology and proven reliability are of utmost importance. they are regularly used in communication and research satellites and fit equally well into aircraft and military elec tronic systems. approval of the tnps .... escc products is granted by the european space components coordination and registered in the escc qualified parts list, rep 005, document number 28789. packaging type code quantity carrier tape width pitch reel diameter tnpw0402 rt7 = td 10 000 paper tape acc. iec 60286-3 type i 8 mm 2 mm 180 mm/7" tnpw0603 tnpw0805 tnpw1206 tnpw1210 r52 = cn 1000 (1) 8 mm 4 mm rt1 = ta 5000 rt6 = tc 20 000 330 mm/13" tnpw2010 tnpw2512 r75 = ty 1000 blister tape acc. iec 60286-3 type ii 12 mm 4 mm 180 mm/7"
document number: 31006 for technical questions, contact: thinfilmchip@vishay.com www.vishay.com revision: 31-jan-12 349 this document is subject to change without notice. the products described herein and this document ar e subject to specific disclaimers, set forth at www.vishay.com/doc?91000 tnpw high stability thin fi lm chip resistors vishay non-linearity current noise hf performance hf performance hf performance hf performance 120 110 100 90 8 0 70 60 10 100 1k 10k 100k resistance value in non-linearity a 3 in db tnpw1206 tnpw0 8 05 tnpw0603 tnpw0402 3 2 1 0.5 0.3 0.1 0.01 0.03 0.05 100 1k 10k 100k 1m resistance value in current noise in v/v tnpw0402 tnpw0 8 05 tnpw0603 tnpw1206 60 40 20 0 - 20 - 40 - 60 - 8 0 15 10 50 100 500 frequency f in mhz phase an g le in ? tnpw0603 10 100 1 k 4.75 k 10 k 1000 60 40 20 0 - 20 - 40 - 60 - 8 0 tnpw0603 15 10 50 100 500 1000 frequency f in mhz [z]-ro in % ro 10 100 1 k 4.75 k 10 k 60 40 20 0 - 20 - 40 - 60 - 8 0 phase an g le in ? 1 5 10 50 100 500 frequency f in mhz tnpw0 8 05 10 100 1 k 10 k 1000 60 40 20 0 - 20 - 40 - 60 - 8 0 [z]-ro in % ro 1510 50 100 500 1000 frequency f in mhz tnpw0 8 05 10 100 1 k 10 k
www.vishay.com for technical questions, contact: thinfilmchip@vishay.com document number: 31006 350 revision: 31-jan-12 tnpw vishay high stability thin fi lm chip resistors this document is subject to change without notice. the products described herein and this document ar e subject to specific disclaimers, set forth at www.vishay.com/doc?91000 temperature rise derating single-pulse high voltage overload test 1.2/50 s en 140000 4.27 single-pulse high voltage overload test 10/700 s en 140000 4.27 pulse rating p ? 0 pulse rating p ? p 70 90 8 0 70 60 50 40 30 20 10 0 0 power in w temperature rise in k 0402 0603 0 8 05 1206 1210 2010 2512 0.1 0.2 0.3 0.4 0.5 0.6 0.7 120 100 8 0 60 40 20 0 - 55 - 25 0 25 50 75 100 125 150 175 ambient temperature in c rated power in % 70 en 3k 1k 100 10 10r 100r 1k 10k 100k resistance value in test volta g e in v tnpw0 8 05 tnpw0603 3k 1k 100 10 10r 100r 1k 10k 100k test volta g e in v tnpw0 8 05 tnpw0603 resistance value in 100 10 1 0.1 0.01 10 -5 10 -4 10 -3 10 -2 10 -1 110 square pulse t i in s power ratin g p in w secondary conditions: a) p (peak p u lse, single p u lse) b ) ? u 70 c c) ? max. see diagram (max. p u lse v oltage) tnpw0 8 05 tnpw0603 > 0 100 10 1 0.1 0.01 10 -5 10 -4 10 -3 10 -2 10 -1 110 square pulse t i in s secondary conditions: a) p 70 (permissi b le constant po w er at ? u = 70 c) b ) ? u 70 c c) ? max. see diagram (max. p u lse v oltage) power ratin g p in w tnpw0 8 05 tnpw0603 p
document number: 31006 for technical questions, contact: thinfilmchip@vishay.com www.vishay.com revision: 31-jan-12 351 this document is subject to change without notice. the products described herein and this document ar e subject to specific disclaimers, set forth at www.vishay.com/doc?91000 tnpw high stability thin fi lm chip resistors vishay test and requirements all tests are carried out in accordance with the following specifications: iec 60115-1, generic specification (includes tests) en 140400, sectional specificat ion (includes schedule for qualification approval) en 140401-801, detail specification (includes schedule for conformance inspection) the testing also covers most of the requirements specified by eia/is-703 and jis-c-5202. the tests are carried out under standard atmospheric conditions in accordance with iec 60068-1, 5.3. climatic category lct/uct/56 (rated temperature range: lower category temperature, upper category temperature; damp heat, long term, 56 days) is valid. unless otherwise specified the following values apply: temperature: 15 c to 35 c relative humidity: 45 % to 75 % air pressure: 86 kpa to 106 kpa (860 mbar to 1060 mbar). the components are mounted for testing on boards in accordance with en 60115- 1, 4.31 unless otherwise specified. the parameters stated in the test procedures and requirements table are based on the required tests and permitted limits of en 140401-801. maximum pulse voltage 500 400 300 200 100 0 square pulse t i in s 10 -5 10 -4 10 -3 10 -2 10 -1 110 secondary conditions: a) p see diagram (p u lse rating) b ) ? u 70 c pulse vo lta g e ? max. in v tnpw0 8 05 tnpw0603
www.vishay.com for technical questions, contact: thinfilmchip@vishay.com document number: 31006 352 revision: 31-jan-12 tnpw vishay high stability thin fi lm chip resistors this document is subject to change without notice. the products described herein and this document ar e subject to specific disclaimers, set forth at www.vishay.com/doc?91000 test procedures and requirements en 60115-1 clause iec 60068-2 test method test procedure requirements permissible change ( ? r) stability for product types: tnpw0402 10 ? to < 100 ? 100 ? to 100 k ? 10 ? to 100 k ? tnpw0603 100 ? to 332 k ? 10 ? to 332 k ? tnpw0805 100 ? to 1 m ? 10 ? to 1 m ? tnpw1206 100 ? to 2 m ? 10 ? to 2 m ? tnpw1210 100 ? to 3.01 m ? 10 ? to 3.01 m ? tnpw2010 100 ? to 4.99 m ? 10 ? to 4.99 m ? tnpw2512 100 ? to 8.87 m ? 10 ? to 8.87 m ? 4.5 - resistance 0.1 % 0.5 %; 1.0 % 4.8.4.2 - temperature coefficient at (20/- 55/20) ? c and (20/125/20) c 50 ppm/k; 25 ppm/k; 15 ppm/k; 10 ppm/k 4.25.1 - endurance at 70 ? c u = or ? u max. ; 1.5 h on; 0.5 h off; 70 ? c; 1000 h (0.1 % r +0.02 ? ) (0.05 % r +0.01 ? ) (0.25 % r +0.05 ? ) 4.25.3 - endurance at upper category temperature 125 c; 1000 h (0.1 % r +0.02 ? ) (0.05 % r +0.01 ? ) (0.5 % r +0.05 ? ) 4.13 - short time overload u = 2.5 x ? 2 x u max. ; 5 s (0.05 % r +0.01 ? ) (0.02 % r +0.01 ? ) (0.1 % r +0.02 ? ) 4.19 14 (na) rapid change of temperature 30 min at lct: 30 min at uct; lct = - 55 c; uct = 125 c; 5 cycles (0.05 % r +0.01 ? ) (0.02 % r +0.01 ? ) (0.1 % r +0.02 ? ) 4.24 78 (cab) damp heat steady state (40 ? ? 2) c; 56 days; (93 3) % rh (0.1 % r +0.02 ? ) (0.05 % r +0.01 ? ) (0.5 % r +0.05 ? ) 4.18.2 58 (td) resistance to soldering heat solder bath method; (260 5) c; (10 1) s (0.05 % r +0.01 ? ) (0.02 % r +0.01 ? ) (0.1 % r +0.02 ? ) p 70 x r p 70 x r
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
